North East Xterra Club https://www.nexterra.org/forums/ |
|
Bklyn.X https://www.nexterra.org/forums/viewtopic.php?f=71&t=2157 |
Page 8 of 15 |
Author: | BKxterra718 [ Thu Aug 24, 2017 1:29 am ] |
Post subject: | Re: Bklyn.X |
Bklyn.X wrote: Those are actually chew toys for very large dogs. "Kong"Sent from my iPhone using Tapatalk |
Author: | RomeoEJ [ Fri Aug 25, 2017 4:02 pm ] |
Post subject: | Re: Bklyn.X |
Hahaha very nice! Sent from my iPad using Tapatalk |
Author: | chatnavz [ Fri Aug 25, 2017 8:47 pm ] |
Post subject: | Re: Bklyn.X |
wow! awesome Sent from my SM-G920T using Tapatalk |
Author: | Bklyn.X [ Sat Aug 26, 2017 11:54 am ] |
Post subject: | Re: Bklyn.X |
Okay I cleaned up this thread a bit deleting some photos from photofucket that won’t show any longer and the text that refered to them. I transfered photos I wanted to keep into my NEXterra Photo Gallery All Supporting Members can get a personal gallery like mine (where you can load your photos and share on third party sites) and/or add to existing galleries by becoming a "Member" of the NEXTerra Club. See how HERE. |
Author: | Bass4Runner [ Sat Aug 26, 2017 4:39 pm ] |
Post subject: | Re: Bklyn.X |
They look awesome !! beefy.... |
Author: | Bklyn.X [ Thu Sep 14, 2017 2:41 pm ] |
Post subject: | Re: Bklyn.X |
Before; After: Bled for days…it’s better but still feels spongy. |
Author: | murphy [ Thu Sep 14, 2017 4:30 pm ] |
Post subject: | Re: Bklyn.X |
It's the disappearing ABS trick! Or is it just the metering block? |
Author: | Bklyn.X [ Thu Sep 14, 2017 4:34 pm ] |
Post subject: | Re: Bklyn.X |
ABS out. I wanted to try that before swapping out the MC. I still need to do that. |
Author: | Bklyn.X [ Mon Oct 16, 2017 11:36 am ] |
Post subject: | Re: Bklyn.X |
This is a Wilwood Aluminum Tandem Chamber Master Cylinder with the Combination Proportioning Valve and Wilwood ten pound residual pressure valve. You can access the specs by clicking the links. I went with this MC on Dave’s (http://bandit4x4.com/) recommendation. He has one in his truck and said he’d help install it (basically install it while I handed him tools). It is a direct swap; take out the OEM MC, the pin part of the output rod length adjuster and ABS module. Bench bleed the Wilwood MC, bolt it to the brake booster with the OEM hardware, connect the fluid lines, connect the pressure valve, bleed the system. This MC kit ain’t cheap but you get what you pay for, again, check the specs HERE. Considering that lack of specific info on others SAS brake setups on 1st Gen SAS’d trucks I could find, that I knew it would fit, that Dave was going to install it and that I would learn how to do something it was kinda a no brainer. OEM out, residual pressure valve installed. MC installed; Bleeding a brake system is always a PITA even with speed bleeders but after a few times around we got it done. The brakes felt spongy with the OEM MC even after the ABS delete but would stop the truck. I took it to the NEXTerra B2SR17 and they held fine on the trail. They just didn’t instill any kind of confidence. With the Wilwood installed I was able to stop the truck in about 30 feet from 30mph leaving a skid mark. On the drive back to Brooklyn the brakes felt stronger than the OEM system pre SAS. I’m happy, money and time well spent. Thanks Dave! |
Author: | Bandit4x4 [ Mon Oct 16, 2017 12:53 pm ] |
Post subject: | Re: Bklyn.X |
No worries BklynX, brakes are important and a great place to spare no expense! Enjoy smoking the pads! Sent from my iPhone using Tapatalk |
Author: | Bass4Runner [ Mon Oct 16, 2017 7:24 pm ] |
Post subject: | Re: Bklyn.X |
Awesome !! looks great money well spent |
Author: | RomeoEJ [ Mon Oct 16, 2017 7:45 pm ] |
Post subject: | Re: Bklyn.X |
Very nice! Sent from my iPhone using Tapatalk |
Author: | murphy [ Tue Oct 17, 2017 4:24 am ] |
Post subject: | Re: Bklyn.X |
I hope the skid marks were on the pavement. Dave is right. It sounds like the expense was worth it. Stopping is just as important as going. |
Author: | Bklyn.X [ Mon Nov 13, 2017 3:24 pm ] |
Post subject: | Re: Bklyn.X |
Leo helped me (did all the work while handed him tools and ate the freshly baked Empanadas his Grandmother made us) install my NOCO IGD140HP Battery Isolator yesterday! It fit nicely in the spot previously occupied by my ABS unit. Leo is an artist with electronics. Thank you my brother! |
Author: | Bass4Runner [ Mon Nov 13, 2017 7:32 pm ] |
Post subject: | Re: Bklyn.X |
Awesome Tom !! Nice work as always Leo |
Page 8 of 15 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |