North East Xterra Club
https://www.nexterra.org/forums/

1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE
https://www.nexterra.org/forums/viewtopic.php?f=107&t=9316
Page 1 of 1

Author:  Bandit4x4 [ Wed Jun 07, 2017 1:51 pm ]
Post subject:  1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Image

Image
Slip yoke eliminator for the Nissan Xterra TX-10 transfer case converts your rear output to a 1350/1410 Companion Flange!

go big or Go homeā€¦ broken!

Email for details

Sales@bandit4x4.com


Sent from my iPhone using Tapatalk

Author:  RomeoEJ [ Wed Jun 07, 2017 7:07 pm ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Very nice!


Sent from my iPad using Tapatalk

Author:  Bandit4x4 [ Sat Jul 29, 2017 7:08 am ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

FYI.... One (1) was snagged at ECXC for a considerable discount! Enjoy Ernie! Email or call me for install info!


Sent from my iPhone using Tapatalk

Author:  Bklyn.X [ Sat Jul 29, 2017 9:18 am ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Very nice.


Sent from my iPhone using Tapatalk

Author:  Bass4Runner [ Sat Jul 29, 2017 9:52 pm ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Thank you !!
It's an awesome piece, great quality as in all of the Bandit 4x4 products.
defiantly a great mod for all the first gen owners out there.

will do :thumbup: on the install instructions ...
doing a custom gas tank mod right now :roll: ..lol :lol: :lol:

Author:  Bandit4x4 [ Sun Jul 30, 2017 5:02 am ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Bass4Runner wrote:
...
doing a custom gas tank mod right now :roll: ..lol :lol: :lol:


Thanks for the fill up

I needed those 4 cups of fresh gas lol


Sent from my iPhone using Tapatalk

Author:  Bandit4x4 [ Thu Aug 03, 2017 9:10 am ]
Post subject:  1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Bass4Runner wrote:
Thank you !!
It's an awesome piece, great quality as in all of the Bandit 4x4 products.
defiantly a great mod for all the first gen owners out there.

will do :thumbup: on the install instructions ...
doing a custom gas tank mod right now :roll: ..lol :lol: :lol:


Carbide round burr grinder a must ImageImageImage + the thickness of the cutoff wheel

Image some solid carbide bits from McMaster to get a nice pilot hole

Then use the round burr grinder to clean out the case hardened in the hole that factory uses to balance/ hold tail shaft while cutting splines. Then step up to a 1/2-20 tap drill (29/64) High speed jobber bits did the best! More aggressive cutting tip (118deg) and use a 130 set to finish hole

Hole depth about 1-5/8...

Tap with both a starting and bottoming tap

Tap as deep as possible


Depending on age and appearance of rear t-case seal replace if necessary...

If case has crawler gears... this should be the "last time" to install/remove the SYE, I put a bit of Loctite Anaerobic gasket maker on the splines then red loctited the 1/2-20 bolt in with a 1.75 OD 9/16 ID thick style washer

Image

Drill, I used a 18v Milwaukee fit in there nice and worked great

Sent from my iPhone using Tapatalk

Author:  Bass4Runner [ Thu Aug 03, 2017 4:12 pm ]
Post subject:  Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE

Awesome !! :woohoo:
Thank you :thumbup:
and great write up.

Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/