Slip yoke eliminator for the Nissan Xterra TX-10 transfer case converts your rear output to a 1350/1410 Companion Flange!
go big or Go home… broken!
Email for details
Sales@bandit4x4.com
Sent from my iPhone using Tapatalk
| North East Xterra Club https://www.nexterra.org/forums/ |
|
| 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE https://www.nexterra.org/forums/viewtopic.php?f=107&t=9316 |
Page 1 of 1 |
| Author: | Bandit4x4 [ Wed Jun 07, 2017 1:51 pm ] |
| Post subject: | 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Slip yoke eliminator for the Nissan Xterra TX-10 transfer case converts your rear output to a 1350/1410 Companion Flange! go big or Go home… broken! Email for details Sales@bandit4x4.com Sent from my iPhone using Tapatalk |
|
| Author: | RomeoEJ [ Wed Jun 07, 2017 7:07 pm ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Very nice! Sent from my iPad using Tapatalk |
|
| Author: | Bandit4x4 [ Sat Jul 29, 2017 7:08 am ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
FYI.... One (1) was snagged at ECXC for a considerable discount! Enjoy Ernie! Email or call me for install info! Sent from my iPhone using Tapatalk |
|
| Author: | Bklyn.X [ Sat Jul 29, 2017 9:18 am ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Very nice. Sent from my iPhone using Tapatalk |
|
| Author: | Bass4Runner [ Sat Jul 29, 2017 9:52 pm ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Thank you !! It's an awesome piece, great quality as in all of the Bandit 4x4 products. defiantly a great mod for all the first gen owners out there. will do  on the install instructions ...doing a custom gas tank mod right now  ..lol 
|
|
| Author: | Bandit4x4 [ Sun Jul 30, 2017 5:02 am ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Bass4Runner wrote: ... doing a custom gas tank mod right now ..lol Thanks for the fill up I needed those 4 cups of fresh gas lol Sent from my iPhone using Tapatalk |
|
| Author: | Bandit4x4 [ Thu Aug 03, 2017 9:10 am ] |
| Post subject: | 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Bass4Runner wrote: Thank you !! It's an awesome piece, great quality as in all of the Bandit 4x4 products. defiantly a great mod for all the first gen owners out there. will do on the install instructions ...doing a custom gas tank mod right now ..lol Carbide round burr grinder a must    + the thickness of the cutoff wheel some solid carbide bits from McMaster to get a nice pilot holeThen use the round burr grinder to clean out the case hardened in the hole that factory uses to balance/ hold tail shaft while cutting splines. Then step up to a 1/2-20 tap drill (29/64) High speed jobber bits did the best! More aggressive cutting tip (118deg) and use a 130 set to finish hole Hole depth about 1-5/8... Tap with both a starting and bottoming tap Tap as deep as possible Depending on age and appearance of rear t-case seal replace if necessary... If case has crawler gears... this should be the "last time" to install/remove the SYE, I put a bit of Loctite Anaerobic gasket maker on the splines then red loctited the 1/2-20 bolt in with a 1.75 OD 9/16 ID thick style washer  Drill, I used a 18v Milwaukee fit in there nice and worked great Sent from my iPhone using Tapatalk |
|
| Author: | Bass4Runner [ Thu Aug 03, 2017 4:12 pm ] |
| Post subject: | Re: 1999-2004 Frontier & 2000-2004 Xterra - TX-10 SYE |
Awesome !!  Thank you and great write up. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|