North East Xterra Club https://www.nexterra.org/forums/ |
|
Saturday March 12 https://www.nexterra.org/forums/viewtopic.php?f=10&t=8838 |
Page 1 of 1 |
Author: | TomsRedX [ Sun Mar 06, 2016 11:18 pm ] |
Post subject: | Saturday March 12 |
Cochranvill, Pa. Body lift and titan suspension swap. Heated garage included. Come on out and bust some knuckles with me, it will be fun! Sent from my SM-N900V using Tapatalk |
Author: | BKxterra718 [ Mon Mar 07, 2016 9:42 am ] |
Post subject: | Re: Saturday March 12 |
Haha nice! Im doin my BL the same day! |
Author: | c3PO [ Mon Mar 07, 2016 1:24 pm ] |
Post subject: | Re: Saturday March 12 |
Sounds fun but you're too far and Im out of town. Have plenty of blades to remove the LCAs and a puller to seperate the lower ball joint. Good luck. |
Author: | TKX [ Mon Mar 07, 2016 1:48 pm ] |
Post subject: | Re: Saturday March 12 |
Tom, what are you doing up front? M205 or staying locked r180? Sent from my SM-G920V using Tapatalk |
Author: | TomsRedX [ Tue Mar 15, 2016 10:36 pm ] |
Post subject: | Re: Saturday March 12 |
Locked r180, got a spare extended axle for when I need one. Didn't get to the suspension, broke a body mount bolt and a rear bumper mount bolt. Got the body lift done around 2 then helped Stephen Q finish installing the lift on his dads frontier. Didnt get done till 10pm, long day. |
Author: | TomsRedX [ Tue Mar 15, 2016 10:38 pm ] |
Post subject: | Re: Saturday March 12 |
c3PO wrote: Sounds fun but you're too far and Im out of town. Have plenty of blades to remove the LCAs and a puller to seperate the lower ball joint. Good luck. I put camber bolts in and check them on occasion to make sure they are still free so no worries there. Have puller ready to go. |
Author: | BKxterra718 [ Wed Mar 16, 2016 10:05 am ] |
Post subject: | Saturday March 12 |
TomsRedX wrote: Locked r180, got a spare extended axle for when I need one. Didn't get to the suspension, broke a body mount bolt and a rear bumper mount bolt. Got the body lift done around 2 then helped Stephen Q finish installing the lift on his dads frontier. Didnt get done till 10pm, long day. Glad u got it done despite the bolt. I was sprayin my rig for 3 weeks before the lift. Long day, def hear that. Me and my girl didnt finish the 2"BL on the fronty till midnight. Took me 10hrs. Ran into several complications. Steering shaft wouldnt retighten, radiator drain plug broke had to extract and replace, and rear bumper bolts all seized. Couldnt fig out the lift for the bed. A/C's instructions are crap. I cut off a mount bolt i needed, wound up punchin it out w an air hammer and just usin a 3/8 bolt it holds better than the Nissan factory one. Anyways if anyones wonderin on a frontier crew cab the 2x2x4 brackets go on the cab side of the bed and the 2" pucks go on the rear. The rubber washers go between the pucks/brackets and the frame. I had to find out the hard way. And yes 10hrs, i did it with love and care for each nook and cranny. |
Author: | TomsRedX [ Wed Mar 16, 2016 10:27 am ] |
Post subject: | Re: Saturday March 12 |
My lift didn't come with any instructions or relocation brackets so had to do some fab work. There's a good how too that I somewhat followed. Sent from my SM-N900V using Tapatalk |
Author: | MtDewMike [ Wed Mar 16, 2016 12:08 pm ] |
Post subject: | Re: Saturday March 12 |
TomsRedX wrote: My lift didn't come with any instructions or relocation brackets so had to do some fab work. There's a good how too that I somewhat followed. Sent from my SM-N900V using Tapatalk Where did you get your BL from, Tom? Mine came from Brian @ Cherry Hill, and he provided instructions. |
Author: | TomsRedX [ Wed Mar 16, 2016 11:08 pm ] |
Post subject: | Re: Saturday March 12 |
Came from NISSTEC, won it in the raffle at WENT. Came with the pucks, zipties and upper radiator hose. Had to cut the hose to make it fit right. |
Author: | MtDewMike [ Thu Mar 17, 2016 11:13 am ] |
Post subject: | Re: Saturday March 12 |
Yeah, we had to trim the radiator hose a bit that came with the Cherry Hill kit, too. |
Page 1 of 1 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |